You will need a custom Macro

This works on a similar machine here % O0001 (Temp) (DOOSAN-4AXV) (MACHINE GROUP-1) (MCX FILE - TEMP) (PROGRAM - Temp.NC) (DATE - MAR-15-2019) (TIME - 7:33 AM) (T219 - 10. FLAT ENDMILL - H219 - D219 - D10.000mm) G00 G17 G21 G40 G80 G90 G91 G28 Z0. (COMPENSATION TYPE - COMPUTER) N219 T219 M06 ( 10. FLAT ENDMILL) (MAX - Z50.) (MIN - Z0.) M11 (UNLOCK) G00 G17 G90 G54 A0. X5. Y41.612 S3500 M03 M10 (LOCK) G49 G94 G05.1 Q1 R5 G43 H219 Z50. Z10. G01 Z0. F3.6 Y0. G00 Z50. M11 (UNLOCK) A270. X5. Y41.612 M10 (LOCK) Z50. Z10. G01 Z0. Y0. G00 Z50. M11 (UNLOCK) A180. X5. Y41.612 M10 (LOCK) Z50. Z10. G01 Z0. Y0. G00 Z50. M11 (UNLOCK) A90. X5. Y41.612 M10 (LOCK) Z50. Z10. G01 Z0. Y0. G00 Z50. G05.1 Q0 M09 M05 G91 G28 Z0. M11 (UNLOCK) G28 Y0. A0. M10 (LOCK) G90 M30 %

At a guess M11/M10

Yes draw the OD line at an angle

^^ Agree totally ^^

Onboard graphics are not supported. You could try turning off the graphics acceleration that may fix it

Nice work, Thank you for sharing

Seems odd eh

Gee that's quiet specific, do you have a post error?

Hi All, Does anybody have the post processor manual for a MAZAK VTC-800/30SR 5 axis Mill that they can share? Thanks in Advance

I know of one nearby, what do you want to know?

I use a Dell Precision 5530 small very light and powerful. I use a docking station in my office.

Logitech MX518 here

Here is one from a few weeks ago

Sounds like it is turned off, extend the screen then there should be a display all button there somewhere

Your dealer can get you the one from the Mastercam internal site

I think you should get something like this 1159SMPM50564-13.MIN

The old generic 5 axis post supports this VC200=0.2 (TOOL BREAKAGE TOLERANCE) M404 G0 G17 G40 G80 G90 G94 G0 G16 H0 Z999. M11 M27 G0 A0. C0. (1/2 EM .125R 1.625LOC 2.000CLR 4FL |TOOL - 15|DIA. OFF. - 15|LEN. - 15|TOOL DIA. - .5) (ROUGH SLOT) N1 G116 T15 ( 1/2 EM .125R 1.625LOC 2.000CLR 4FL TOOL - 15 ) G15 H1 G0 G90 C70.4102 A-90. G0 G17 X0. Y-7.09994 S10000 M3 G56 HA Z7.82 M8 Z2.32 G1 Z2.28269 F70. Z2.24538 Z2.20808 Z2.17077 Z2.13346 Z2.09615 Z2.05885 Z2.02154 Z1.98423 Z1.94692 Z1.90962 Z1.87231 Z1.835 Y-7.11351 Z1.83325 C71.3798 F89.35 Y-7.12709 Z1.8315 C72.3494 Y-7.14066 Z1.82975 C73.319 Y-7.15416 Z1.82797 C74.2888 Y-7.15891 Z1.82647 C75.0018 Y-7.16369 Z1.825 C75.7154 C76.4048 C77.0927

Linking %of tool diameter Make the number smaller say 1

the new 3D connexion drivers does not support verify, you will need an old one, see below comments from QC "" Currently the only option is to install an older version of the driver (v10.4.3 or older). Something changed in v10.4.9 and later releases that is causing it not to work in Verify. We do have a defect logged against this but it has yet to be addressed. D-28898 Regards

Nice Work Gracjan, Your numbers look good Attached is what I get when I draw it in NX. hyperboloid parabolic.mcam

Yes that sounds correct You cannot run both G68.2 (TWP) and G43.4 (TCP) together but you can have G68.2 and G43 together

In my experience you will get a better result working the other way, Make an attempt and put some toolpaths on your part, upload the MCX file and then you will get some suggestions

Sounds impressive, do you want to draw one or machine it?

There are a few way to attack this one, it will all depend on how many you need to make. For a few I I would cut the top first then tap the holes and use the tapped holes to hold the part down for Op2